AEG Dishwasher Error Codes List
If we talk about modern AEG dishwashers, we should highlight the ability to independently diagnose its condition. This is extremely convenient, because not every malfunction should be a reason to call a technician. It often happens that the user is able to solve the problem using available tools, so the information hidden in the error codes seems extremely important.
AEG dishwashers are the brainchild of a German company and have high levels of reliability and safety. However, even such equipment is prone to breakdowns and calling a technician, already having an idea of the nature of the malfunction, will be the right decision. As a result, the specialist will take the necessary tools and components, otherwise the repair may be delayed.
It also happens that the owner of the unit does not have to spend money on the services of specialists, because a number of malfunctions can be eliminated independently with a little effort.
TABLE WITH ERROR CODES: AEG DISHWASHERS
|
Fault code |
Number of flashes for Dishwashers with indicator |
Meaning | Reason for appearance | DIY repair |
| I10 | 1 | There is no water in the car. Timeout exceeded. |
1. Problems with the water level sensor. 2. The inlet hose is clogged or pinched. 3. The inlet tap is closed, there is no water in the water supply. 4. The intake valve is broken. |
1. Details are carried out. If it malfunctions, it is replaced. 2. Inspect the inlet hose, clear it from blockages. 3. Checking the water in the water supply. 4. Diagnostics of the filling valve. Replace if necessary. |
| I20 | 2 | No water drainage. |
1. The drain system is clogged. 2. The drain hose is choked. 3. Problems with the water level sensor. 4. Drain pump failure. |
How to fix the situation: 1. Check the drain hose for blockages and kinks. 2. The level sensor is inspected and a new part is installed if there is a problem. 3. The drain pump is inspected and cleared of debris. If the pump is faulty, it must be replaced. |
| I30 | 3 | The Aquastop protection worked. |
Water was found in the dishwasher tray and there was a leak.
Or the float sensor is faulty. |
1. The PMM body and connections are inspected at the time of leakage. 2. Diagnostics of the Aquastop system. |
| I50 | 5 | Problems with the control module. | The triac of the module that controls the pump is faulty. | The main module needs diagnostics and repair. |
| I60 | 6 | What does the code mean: the water is not heating or is overheating. |
1. The heating element has burnt out. 2. Level sensor failure. 3. Pump malfunction. 4. There are problems with the thermistor. 4. The dishwasher control module is faulty. |
What can you do if this code appears: 1. Check and replace the heating element. 2. Inspect the level sensor and its connections. Install a new part if it breaks. 3. If there are problems with the installation of the machine or the pump, the water is constantly drained, so heating does not occur. It is necessary to check the connection system, as well as the functionality of the pump. |
| I70 | 7 | Wiring problems, NTC shorted. | Checking and replacing wiring. Inspect the NTC sensor. | |
| I80 and I90 | 8-9 | Problems with eeprom communication or module firmware. | Electronic module malfunction. | Diagnostics and repair or replacement of the module. |
| IA0 | 10 | The sprinkler does not work. | You need to check and unlock the sprinkler. | |
| IЬ 0 | 11 | There are problems with the turbidity sensor. |
1. Turbidity sensor does not work. 2. The dishwasher needs cleaning. |
1. Check and replace the turbidity sensor. 2. Cleaning the dishwasher. |
| IC0 | 12 | No connection to user interface. | Main module malfunction. System failure. |
The dishwasher needs a reset. If the error does not disappear, the module is diagnosed and repaired. |
| IAd0 | 13 | There is no tachogenerator signal. |
1. No water heating. 2. Uncontrolled engine speed. |
The tachogenerator needs checking and replacement. |
| IF0 | 14 | No water intake. |
Low pressure in the water supply. |
You need to wait until normal water supply resumes. |
i70
This code indicates that the NTC sensor resistance is unacceptable. Causes: short circuit, disconnected contacts. Washing dishes will not stop, but the process will occur without heating. Potential causes are a malfunction of the main control board, a malfunction in the electrical circuit of the sensor, or failure of the thermistor.
Other Faults
You may encounter difficulties in the operation of the device, even if these AEG dishwasher errors do not have a specific code. Most often, they can be solved very simply; more details about this are written in the instructions for your model. Here are the most common problems:
- The dishwasher won't turn on. Check the connection of the network cable to the device, the operation of the socket, and the integrity of the electrical panel.
- After selecting a program, it does not start. Open and close the door again. Make sure that the Delay Start function has not been selected. Or wait five minutes—an internal preparation program may be running.
- During operation, the washing cycle stops and then starts again. This is not a malfunction, the device adapts to the specific task and thus ensures energy efficiency and optimal cleaning of dishes.
- Extraneous knocks and sounds are heard from the dishwasher. Check that the sprinklers rotate freely and that the devices are loaded correctly into the basket.
- There is a small leak on the side of the door. It is necessary to level the device horizontally by adjusting the legs.
- The fuse trips. Several devices are turned on at the same time, which overloads the network, or the outlet does not provide the required voltage.